A塑件图
塑料圆罩成型工艺与模具设计
摘要
本设计题目为塑料圆罩成型工艺与模具设计，来源于书籍，体现了典型塑料模的设计要求、内容及方向，有一定的设计意义。通过对该零件模具的设计，进一步加强了设计者塑料模设计的基础知识，为设计更复杂的塑料模具做好了铺垫和吸取了更深刻的经验。
本设计运用塑料成型工艺及模具设计的基础知识，首先分析了塑件的成分及性能要求，为选取浇口的类型做好了准备；然后估算了塑件的体积，便于选取注塑机及确定型腔数量；其次看是否需要侧抽，如需要，选择合适的侧抽机构，确定其工作原理；最后分析了塑件的特征，确定模具的设计参数、设计要点及推出装置的选龋
关键词：注塑模浇口
Plastic molding process and die design of protective cover
Abstract: This design topic is cover plastic molding process and mold design protection,from books,reflects the typical plastic mould design requirements,content and direction,the design of a certain significance.Through the design of the die parts,further strengthen the designers of basic knowledge of plastic mold design,paving thewayand drawa more profound experience for the plastic mold design more complex.
This design using the basic knowledge of plastic molding process and mold design,first analyzes the composition and performance of the plastic parts,readyto select the type of gate; plastic parts and estimated thevolume,to select the injection molding machine and determine the number of cavities; secondlywhether need to side,if necessary,select the appropriate the side core pulling mechanism,itsworking principle is determined; finallyanalyses the characteristics of plastic parts,determination of design parameters,die design and the introduction of the selected devices.
Keywords: gate side
目录
1.绪论...........................................................1
1.1塑料制品和注射成形在模具业的重要地位............................1
1.2模具在我国的发展历程............................................1
1.3前景展望........................................................2
2塑料制件的分析....................................................3
2.1成型塑料件的工艺分析............................................3
2.2成型塑件的材料分析..............................................5
3塑件成型的基本过程................................................6
3.1塑件成型的基本过程..............................................6
3.2分型面的选择....................................................7
4注塑设备的选择....................................................8
4.1估算塑件体积质量................................................8
4.2注塑机的选择....................................................8
5成型零件有关尺寸的计算............................................9
6模具各系统的设计.................................................15
6.1浇注系统的设计.................................................15
6.1.1浇口套的选用.................................................15
6.1.2交口位置的选择...............................................16
6.2合模导向机构的设计.............................................17
6.2.1导柱的设计...................................................17
6.2.2导套的设计...................................................18
6.3.脱模结构的设计.................................................19
6.4排气系统.......................................................20
6.5冷却系统.......................................................21
6.6绘制装配图及定制零件明细表.....................................22
7注塑机的校核.....................................................26
7.1注射量的校核...................................................26
7.2锁模力的校核...................................................26
7.3磨具厚度的校核.................................................26
7.4开模行程校核...................................................27
结论...........................................................28
致谢...........................................................29
参考文献...........................................................30
A注塑模装配图
垫块
定模座板
动模板
动模座板
推件板
型腔镶件
型芯
1字数
2摘要
3目录
4动模板过程卡
5定模板过程卡
