尾座体架的铣Φ17H6孔两端面夹具设计及加工工艺即铣Φ35两端面含SW三维及9张CAD图+说明书

三维零件图

摘要
本课题主要是设计尾座体的加工工艺及夹具的设计，在设计中采用先设计该尾座体的加工工艺在根据加工工艺来选取夹具的设计的方案和夹具的具体设计；而设计的重点是夹具的设计。由于工件的孔17和14都要以底面做为基准加工，故首先得做出底面的加工夹具。由于孔17的精度要求高，和定位尺寸误差小，为保证孔的位置和加工准确性我们一定在加工底面的时间通过画线找出底面的加工余量。这样就可以更好的保证孔17的位置和加工精度！加工孔14的夹具其实就是在加工底面夹具的基础上加了一个45度斜度板。加工孔17的时间为保证相对于A和B面的平行度我们就得要准确的设计出以A和B面定位的夹具！还考虑到工件的圆度和圆柱度的误差小，我们设计的夹具就具有对孔17的夹具定位准确，和加工时间的震动小的要求，那就得在孔17的附近找个定位加紧点！
关键词加工工艺，夹具，尾座体，设计
ABSTRACT

This topic is mainly design that designs the tail a body of some tool machine to process the craft and tongses, adopting to design first in the design a body of that tail processes the craft at according to process the craft to select by examinations the tongs of the project of the design and concrete design of the tongs;But the point of design is the design of the tongs.Because the bore of the work piece 17 and 14 all want to face to be used as the basis to process with the bottom, past have to do a bottom to face first of process the tongs.Because bore 17 of accuracy have high request, and position the size error margin small, for guarantee the position of the bore and process the accuracy we certainly at process the bottom to face of time pass to draw the line to find out the bottom to face of process the amount of remaining.Thus can with better assurance bore 17 of position and process the accuracy!Process the bore 14 of tongs was in processing the foundation that the bottom faces the furniture to add one 45 degrees of gradient plank in fact.Process the bore 17 of time is opposite for assurance to run parallel with B face of in the A we have to design accurately with the AN and B faces to settle for of tongs!Return in consideration of a degree of the work piece and the error margin of the cylinder degrees are small, the furniture that we design have to the bore 17 of tongs fixed position is accurate, and process the vibration of time small, that have to in the bore 17 of neighborhood seek a fixed position to step up the point!

Keyword process the craft, tongs, a body of tail, design

目录

摘要I
ABSTRACT II
1前言2
2零件分析3
图1. 3
2.1零件的特点3
2.2零件工艺分析4
3工艺规程设计5
3.1确定毛坯的制造形成5
3.2基面的选择5
3.3制定工艺路线5
3.4机械加工余量、工序尺寸及毛坯的确定9
3.5确定切削用量及基本工时12
第4章夹具设计26
4.1机床夹具的介绍26
4.2铣床夹具的设计31
致谢37
参考文献38

三维夹具装配图

A2-尾座体零件图

A0-夹具装配体

加工过程卡

毛坯图三维

设计目录

摘要部分

字数统计

A2-夹具零件图二

A2-尾座体毛坯图

A2-支撑板

A4-挡块

A4-压板

夹具设计部分

设计所包含文件

A2-夹具零件图

A2-夹具箱体

工序5

工序6

工序8

工序1

工序2

工序3

工序4

工序7