活门的冲压工艺及级进模具设计-带孔长方形垫板冲孔落料冲裁模连续级进模含14张CAD图+说明书

工件图

活门的冲压工艺及级进模具设计【带孔长方形垫板冲孔落料冲裁模连续级进模】
摘要：本设计题目为活门件，体现了典型冲裁模的设计要求、内容及方向，有一定的设计意义。通过对该模具的设计，加强了设计者对冲裁模设计基础知识的理解和运用，为设计更复杂的冲裁模具做好了铺垫。本设计运用冲裁工艺及模具设计的基础知识，首先分析了板材的性能要求，为选取模具的类型做好了准备；然后计算了冲裁件的冲裁力，便于选取压力机吨位及确定压力机型号；最后分析了冲裁件的特征，便于确定模具的设计参数、设计要点及卸件装置。本设计采用了冲孔—落料级进模成形活门制件。成形原理可划分为两个阶段：首先冲孔凸模与凹模共同作用先冲出活门制件上的孔，而后利用第一步冲出的两个10mm的半圆孔做精确定位使外形凸模与凹模共同作用使工件落料成形。
关键词：冲孔—落料级进模冲孔凸模凹模压力机吨位
Thevalve ramming craft and the level enter the mold design
Abstract: This design topic for thevalve punching die, has manifested the typical punching die design request, the content and the direction, has certain design significance.Through to this mold design, strengthened the designer to the punching die design elementary knowledge understanding and the utilization, for designed the more complex blanking mold to complete the upholstery.This design the elementary knowledgewhich designs using the blanking craft and the mold, first has analyzed the plate performance requirement, for selected the mold the type to prepare for; Then has calculated the blanking blanking force, is advantageous for the selection press tonnage and the definite press model; Finally has analyzed the blanking characteristic, is advantageous for determines the mold the designvariable, the design main point and the shedder.This design used the punch holes- to fall the material level to enter the mold formingvalveworkpiece.The formed principle may divide is two stages: First the punch holes raised mold and the concave mold affect together run out on thevalveworkpiece first the hole, after but uses two 10mm half round holewhich first step runs out to make the pinpointing to cause the contour raised mold and the concave mold affects together causes thework piece to fall the material forming.
Keyword: The punch holes- fall the material level to enter the mold punch holes raised mold Concave mold Press tonnage
目录
绪论……………………………………………………………………………1
1.1国内模具的现状和发展趋势………………………………………………1
1.1.1国内模具的现状…………………………………………………………1
1.1.2国内模具的发展趋势……………………………………………………2
1.2国外模具的现状和发展趋势………………………………………………2
1.3活门冲孔落料级进模具设计与制造方面…………………………………3
1.3.1活门冲孔落料级进模具设计的设计思路………………………………3
1.3.2活门模具设计的进度……………………………………………………3
1工艺性分析……………………………………………………………………5
2冲压工艺方案的确定…………………………………………………………6
3排样设计………………………………………………………………………7
3.1确定零件的排样方案…………………………………………………………7
3.2条料宽度、导料板间距离和材料利用率的计算……………………………7
4模具结构形式的选择与确定…………………………………………………9
5冲压力与压力中心的计算………………………………………………………10
5.1冲裁工序总力的计算…………………………………………………………10
5.2初选压力机……………………………………………………………………11
5.3压力中心的计算………………………………………………………………11
6模具主要零件……………………………………………………………………13
6.1工作零部件的设计与标准化……………………………………………13
6.2定位装置的设计与标准化……………………………………………………18
6.3标准模架的选用………………………………………………………………19
6.4卸料部件的设计与标准化……………………………………………………20
7模具装配与调试…………………………………………………………………21
7.1安装总述………………………………………………………………21
7.2模具装配过程…………………………………………………………………21
8垫片冲孔落料连续模总装图……………………………………………………23
9压力机的校核…………………………………………………………………24
结束语………………………………………………………………………………25
致谢…………………………………………………………………………………26
参考文献……………………………………………………………………………27

装配图

凹模板

冲孔凸模

导料板1

导料板2

导正销

垫板

工序卡

过程卡

零件分析

落料凸模

排样图

上模座

设计目录

设计摘要

设计字数统计

凸模固定板

下模座

卸料板