X5230普通铣床数控化改造设计含5张CAD图-版本2+说明书

机床结构图

X5230普通铣床数控化改造
摘要
数控机床以它生产效率高、可加工零件多样化的特点，越来越显示出它的优越性，然而，很多资深的老企业还存在着许多原有的普通机床，如何将普通机床改造成数控机床，已成为机械加工设备改造工作的重点。
本文以X5230普通铣床为例阐述了对普通机床进行技术改造的必要性，提出了该机床数控化改造的方案并实施了改造。机械部分改造主要做了以下工作：将三个进给方向的滑动丝杠改为滚珠丝杠，用伺服步进电机和减速齿轮来实现进给部分的调速，这样不仅提高了传动效率而且可以实现快速定位和准确的启、停；数字控制系统选用南京华兴数控设备有限责任公司生产的WA310M，该系统达到数字化控制各部件协调工作，而且成本低；电气改造中取消原机床强电柜中的大量电气元件，改用继电器、接触器以及伺服驱动器来实现电路的控制。对改造后的机床进行了几何精度和工作精度测试，测试结果满足机床的精度要求，根据测试结果验证了机床改造的可行性和可靠性，不仅加工范围增大，同时降低了劳动强度，提高了加工效率。
与改造前相比，该机床的操作更加方便，大大降低了劳动者的劳动强度，提高了生产效率，改造后的铣床可提高生产效率，保证产品质量和减轻工人的劳动强度,该方案具有投资少、见效快的优点，值得推广。
关键词：数控机床；数控化改造；数控系统

Abstract

Based on its high production efficiency, machinable parts diversification, CNC machine has increasingly shown its superiority. However, many senior enterprises still have large amount of original general-purpose machine tools, how to transform the ordinary tools into CNC machine tools has became the focus of the mechanical processing equipment modification.
Based on X5230 general milling machines, this paper expounds the necessity of the technological transformation to general-purpose machine tools, and purposed transformation of the CNC program and implemented a transformation. Mechanical parts reconstruction made the following job: taking the three feeding direction of sliding screw instead of ball screw, servo stepping motor and reduction gear to realize the speed regulation of the feed part, thisworks not only improve the transmission efficiency,but also achieve rapid positioning and accurate start, stop. Digital control system chooses WA310M NC systemwhich produced by Nanjing Huaxing NC equipment ll cLimited liabiility company. This system chieves the digital control components coordinatework, and the cost is low. Electric system transformation cancelled a large number of electronic components in high electrical cabinet; achieve the control circuit by switch relays, contactors, and servo drive. Then, testing precision and geometry accuracy of the machine after transformation, the test results meet the machine's accuracy. The test resultsverified the feasibility and reliability of machine tools, not only the processing expanded, and the labor intensity reduce, the machining efficiency improved.
Comparedwith before modification, the machine's operations are more convenient, and greatly reduce the laborer labor intensity, improve the production efficiency and product quality. This scheme has advantage of little investment and instant effect,which isworth popularizing.

Keywords: NC machine tool，modifieation of machinetool，NC system

目录
1．绪论1
1．1课题的研究目的和意义1
1．2本文的选题及主要研究内容2
1．1．1主要研究内容2
1．1．2数控化改造的主要环节2
2． X5230普通铣床数控化改造方案的设计5
2．1设计要求5
2．1．1总体改造方案5
2．1．2数控铣床改造后技术参数8
2．2传动系统改装设计与计算9
2．2．1纵向进给系统的设计与计算9
2．2．2横向进给系统的改造设计与计算20
2．2．3垂向进给系统的改造设计与计算25
2．3步进电机的选择31
2．3．1纵向进给系统步进电机的确定31
2．3．2横向进给系统步进电机的确定32
2．3．3垂向进给系统步进电机的确定33
3． X5230铣床数控化改造的数控系统35
3．1数控系统选型35
3．2步进电动机的驱动器选型37
3．2．1驱动器选型37
3．2．2分配器39
3．2．3放大器41
3．2．4系统连接42
3．3驱动器信号输入输出43
3．3．1信号输入输出43
3．3．2面板开关说明45
4． XK5230电气系统数控改造设计46
4．1概述46
4．2电气系统数控改造设计46
4．3强电柜的安装与连接47
参考文献49
致谢48

垂向进给系统装配图

电路图

横向进给系统装配图

纵向A0

1字数

3设计所包含文件

2说明书前三页