外螺纹接头塑件三维
外螺纹接头的注塑模具设计
摘要
此次的设计任务即外螺纹接头注塑模具设计。
产品的3D建模，借助UG设计软件创建型腔、活块以及其他零件，并自动生成所需要的零件工程图；使用草图和厚度检测，评估零件；对于模架的设计,利用UG模座专家胡波来完成,从标准模架选择到产品输出,全部采用3D化设计。我在外螺纹接头模具设计过程中，从零件建模到型腔、型芯的设计、模架设计，直至最后的模具开模动作模拟都充分发挥了UG设计软件的各个模块和插件的优势，基本做到了无图纸化设计。采用一模四腔的设计。注塑机综合注塑容量、锁模力、最大注塑面积和模内压力等技术参数确定注塑机型号选用海天160X2A。模座选用龙记，其他标准件选用Misumi。使用了模具设计软件——UG，从最初的零件3D建模到最后的模具各部分零件的装配，模座设计,工程图文件,依靠UG的各个模块,得到合乎设计规范的工程图。
模具的特点是：产品需要透光性好。此外，还对工作零件和注射机有关参数进行了必要的校核计算。
关键词：外螺纹接头，注塑模具，一模四腔，注塑机
Abstract
The design task is the design of injection mold for external thread joint.
3D modeling of the product, to create a cavity, movable block and other parts are designed by UG software, and automatically generate the required parts drawings; use sketches and thickness detection, evaluation for parts; mold design, mold base by UG experts to complete the Huwave, the output from the standard mold, all using 3D technology design. I am in the external thread joint mold design process from parts modeling to cavity core design, mold design, mold opening action until the end of the simulation and give full play to the UG design software modules and plug-in advantage, basically no design drawings. The design of the first mock exam four cavity. The injection molding machine integrated injection capacity, clamping force, the maximum injection area and mold pressure and other technical parameters to determine the injection molding machine selection Haitian 160X2A. Mold base selection'other standards by Misumi. The use of mold design software-- UG, from the first to the last part 3D modeling of thevarious parts of the mould assembly design, mold base, engineering drawing, rely on the modules of UG, obtained the reasonable design specification of Engineering drawings.
The characteristics of the mold are: the product needs light transmittance. In addition, the necessary parameters of the parts and the injection machine are checked and calculated.
Keywords: external thread joint, injection mold, the first mock exam four cavity, injection molding machine
目录
摘要I
Abstract II
第一章前言1
1.1本课题研究的现状及发展趋势1
1.2本课题研究的意义和价值1
1.3本课题的基本内容，预计解决的难题2
1.4课题的研究方法、技术路线2
1.5研究工作条件和基础3
第二章塑件的分析4
2.1外形的尺寸4
2.2精度等级[4] 4
2．3塑件的结构设计5
2．4塑件尺寸及精度6
2．5塑件表面粗糙度6
2．6塑件的体积和质量6
第三章注塑机选择8
3.1初步选定注射机8
3.2注射机的相关参数选择校核9
3.3设备的型号及选择9
第四章成型零件的设计14
4.1成型零件的结构设计14
4.2浇注系统的设计16
4.3成型零部件的结构设计与计算19
4.4模架的确定22
4.5侧向抽芯机构类型选择23
第五章结论26
参考文献28
致谢29
外螺纹接头注塑模实体三维装配图
外螺纹接头注塑模消隐三维装配图
A4外螺纹接头塑件
A0外螺纹接头注塑模装配图
A1定模板
A1动模板
A2顶针面板
A2滑块
A3推板
A3型腔
A3型芯
设计目录
设计所包含文件
设计字数统计
中英文摘要
