药用内螺纹瓶盖的注塑模设计-注射模含开题及9张CAD图+说明书

3塑件图

摘要：通过分析间断型内螺纹瓶盖的工艺性，可知内螺纹为半圆型螺纹，由于该瓶盖的材料为聚苯乙烯（PS），该材料不宜采用强制脱模。所以塑件采用内抽芯机构进行脱模，由图可知，内螺纹为两个局部段，对应在模具上制成两个内抽的滑块。当动定模分型时，在连接推杆的作用下，八个成型螺纹滑块沿T形槽移出，产生向心的收拢运动。这些滑块始终不脱离型芯座。由于瓶盖的上部分要求严格，所以采用点浇口浇注系统，脱模后不在修正浇口的痕迹。但采用这种浇口时，常常要在模具上增加一个分型面，以便浇口凝料脱模。
关键词：螺纹滑块内抽芯点浇口

Abstract:Pass the analysis interrupteds the craft of a cover of thread inside the type,can knowis a thread of semicircle inside the thread,because of in order to gather the styrene(PS),that bottle of material for cover that material should not adopt to take off the mold compulsory.So an adoption ofinside take out the organization ofto carryon taking off the mold,can knowfrom the diagram,inside the thread is two partial segment,in molding tool ascend make into twoth to should take out of slipperypiece.When move to settle the type of cent of mold,while link the function of push the pole,eight model the thread the slipperypiece follows the T form slot to move,producing to accept the sport of centripetally.These slipperypieces do not escape from a always.Because the upper part of a cover requests separatelystrictly,so the adoption orders to sprinkle to sprinkle to note the system,after taking off the mold not sprinkle the oscular trace in the correction.But adopt this kind of to sprinkle,usuallywant to increase the type of a cent to face on the molding tool,in order to sprinkle a peopleto anticipate to take off the mold.
Keyword:Slipperypiece of thread Inside take out Order to sprinkle

目录

绪论………………………………………………………………………1
第1章模塑工艺规程的编程…………………………………………………3
1.1塑件的工艺性分析………………………………………………………3
1.2计算塑件的体积和重量…………………………………………………4
1.3塑件注塑工艺参数的确定………………………………………………5第2章注塑模的结构设计……………………………………………………6
2.1分型面选择………………………………………………………………6
2.2确定型腔的排列方式……………………………………………………7
2.3浇注系统设计……………………………………………………………8
2.4导柱和导套的选择………………………………………………………10
2.5抽芯机构设计……………………………………………………………11
2.6排气系统的设计…………………………………………………………12
2.7成型零件结构设计………………………………………………………12
第3章模具设计的有关计算………………………………………………15
3.1型腔和型芯工作尺寸计算……………………………………………15
3.2凹模型腔尺寸的计算…………………………………………………15
第4章模具加热与冷却系统的计算………………………………………16
第5章模具闭合高度的确定………………………………………………18
第6章注塑机有关参数的校核……………………………………………19
第7章绘制模具的总装图和非标零件工作图…………………………20
第8章注塑模具的安装和试模……………………………………………21
结论……………………………………………………………………24
致谢……………………………………………………………………25
参考文献………………………………………………………………26

A塑件图

A注塑模装配图

凹模A4

垫块

定模座板

动模板A3

动模座板A3

滑块2

型心座B5

支撑板

1字数

2摘要

4设计所包含文件

5目录

6过程卡