叉形支架零件图A4
测微仪架加工工艺及夹具设计
[摘要]本次是对测微仪架的加工工艺规程设计和其中铣槽工序的专用夹具设计，在零件图的分析下，根据实际生产经验和导师指导的基础上，通过对比多个加工工艺方案优选制定出加工工艺过程。在实际生产过程中，必须按照设计出来的工艺规程规定的方案进行加工，所以制定工艺规程必须要在一定条件下以低成本、高效率的加工完成出符合图纸及技术要求的零件。
在制定出合理的工艺方案时，通过任务书上的要求做出工艺设计说明书和夹具的结构设计。在夹具进行设计时，要求对定位、夹紧等各个部分的计算以及总体布局分析，最后绘制出夹具装配图和零件图。
[关键词]：工艺规程设计；工序；切削用量；夹紧定位
Machining Technology and Fixture Design of Micrometer Frame
[Abstract] This paper is about the design of the processing procedure and the design of the special fixture for the milling process of the micrometer stand. Based on the analysis of the part drawings and the actual production experience and the guidance of the instructor, the processing process is optimized by comparing several processing schemes. In the actual production process, it must be processed according to the plan stipulated by the designed process rules, so the formulation of process rules must be completed under certain conditions with low cost and high efficiency to meet the drawings and technical requirements of the parts.
When formulating a reasonable process plan, the process design instructions and fixture structure design are made according to the requirements of the task book. In fixture design, it is required to calculate and analyze the location, clamping and other parts as well as the overall layout. Finally, the fixture assembly drawing and parts drawing are drawn.
[Keywords] Process planning; Procedure; Cutting parameters; Clamping positioning
目录
1前言………………………………………………………………………………………1
2选题背景…………………………………………………………………………………1
2.1相关课题在当今国内外的现状………………………………………………1
2.2测微仪架数控加工技术的现状………………………………………………2
3零件的工艺分析…………………………………………………………………………2
3.1零件的作用……………………………………………………………………2
3.2零件图的工艺分析……………………………………………………………2
3.3零件图的尺寸标注……………………………………………………………3
4加工工艺方案设计………………………………………………………………………4
4.1确定毛坯的制造方式…………………………………………………………4
4.2定位基准的选择………………………………………………………………4
4.2.1粗基准的选择…………………………………………………………5
4.2.2精基准的选择…………………………………………………………5
4.2.3加工阶段的划分………………………………………………………6
4.2.4机械加工工序…………………………………………………………7
4.3确定工艺方案…………………………………………………………………7
4.3.1制定工艺方案…………………………………………………………7
4.3.2工艺方案的比较与分析………………………………………………9
4.3.3机械加工余量、工序尺寸的确定………………………………………9
4.3.4确定切削用量和基本用时……………………………………………12
5夹具设计………………………………………………………………………………24
5.1问题的提出……………………………………………………………………24
5.2夹具的设计……………………………………………………………………25
6总结……………………………………………………………………………………26
参考文献…………………………………………………………………………………27
致谢………………………………………………………………………………………28
夹具装配图A1
夹具体A2
叉形支架毛坯图
菱形销A4
压板A4
字数统计
夹具设计部分
设计所包含文件
设计目录
铣宽10槽工序卡
加工过程卡
说明书前三页
工序卡
申明：内容来自用户上传，著作权归原作者所有，如涉及侵权问题，请与我们联系，我们将及时处理！
