KT37-12空压机壳体-空气压缩机气缸体的加工工艺及钻2×M8孔夹具设计含2张CAD图+说明书

零件三维

KT37-12空压机壳体-空气压缩机气缸体的加工工艺及钻2×M8孔夹具设计
摘要
夹具是零件加工的夹紧装置，是加工零件的一种必不可少的装置。夹具利用率高，经济性好，对功能组件的使用和数量少。随着零件的尺寸变化，越来越多的夹具被淘汰了，因此，设计一套专用夹具是十分有必要的。在设计专用夹具时要考虑工件的定位方案，工件的夹紧方案和设计夹紧机构，夹具的其他组成部分，夹具的结构形式等。
本次设计的题目是空气压缩机气缸体的加工工艺及钻2×M8孔夹具设计，根据老师给的图纸要求进行工艺设计和夹具设计，在掌握零件作用的基础上，对零件的工艺进行分析。针对设计给定的题目，设计里面主要对机床夹具进行设计。本夹具体是以保证加工精度，生产效率和便于工人操作为宗旨展开的设计。
设计之初我查阅相关数据及国内外关于机床夹具的文献，在看懂零件图的同时对零件的结构和工艺进行分析，明确粗基准和精基准的选择，确定零件的加工余量与毛坯的尺寸、从而确定零件的加工工艺过程、计算各工序的切削用量及工时。最终完成了本次设计所需的夹具。
关键词:空气压缩机气缸体；加工工艺；钻2×M8孔;夹具设计
ABSTRACT
Fixture is a clamping device for parts processing, and is a necessary device for machining parts. The utility rate of the fixture is high, the economy is good, and the use and quantity of the functional components are few. As the size of the parts changes, more and more clamps are eliminated. Therefore, it is necessary to design a set of special fixtures. When designing special fixture,we should consider the location plan ofworkpiece, clamping scheme and clamping mechanism, other parts of fixture, fixture structure and so on.
The design topic is air compressor cylinder body processing technology and drilling 2x M8 hole fixture design, according to the teacher's drawings requirements for process design and fixture design, grasp the role of parts, on the basis of parts process analysis. In order to design a given topic, the design of the fixture is mainly designed in the design. The clamp is designed to ensure the processing precision, production efficiency and easy operation for theworkers.
At the beginning of design I refer to the relevant data and literature at home and abroad on the fixture, structure and process of parts in the read parts map at the same time analysis, clear coarse and fine reference base selection, determine the machining allowance and the size of the blank, so as to determine the parts processing process, calculation of the process of cutting dosage and time. Finally, the fixture required for this design is completed.
Keywords: air compressor cylinder body; processing technology; drilling 2x M8 hole; fixture design
目录
摘要I
ABSTRACT II
第1章绪论2
第2章加工工艺规程设计4
2.1零件的分析4
2.1.1零件的作用4
2.1.2零件的工艺分析5
2.2空气压缩机气缸体加工的主要问题和工艺过程设计所应采取的相应措施5
2.2.1孔和平面的加工顺序5
2.2.2孔系加工方案选择5
2.3空气压缩机气缸体加工定位基准的选择6
2.3.1粗基准的选择6
2.3.2精基准的选择6
2.4空气压缩机气缸体加工主要工序安排7
2.5机械加工余量、工序尺寸及毛坯尺寸的确定10
2.6确定切削用量及基本工时（机动时间）[3] 10
第3章钻2×M8孔夹具设计19
3.1研究原始质料19
3.2定位、夹紧方案的选择19
3.3切削力及夹紧力的计算19
3.4误差分析与计算20
3.5钻套、衬套、钻模板设计与选用21
3.6夹具设计及操作的简要说明23
总结24
参考文献25

夹具装配图

过程卡

夹具设计部分

夹具体

设计目录

设计所包含文件

设计摘要

设计字数统计

钻120度的螺纹孔夹具图二张

工序卡